88 lines
No EOL
3.3 KiB
OpenSCAD
88 lines
No EOL
3.3 KiB
OpenSCAD
// Tube mount for bike trainer control dial
|
|
// length units are millimeters
|
|
// built on its side, so depth is x-axis, height is y-axiz, width is z-axis
|
|
|
|
mountWidth = 25.83;
|
|
mountDepth = 36.7;
|
|
mountHeight = 6.69;
|
|
|
|
rubberHoleWidth = 5.20;
|
|
rubberHoleSunkWidth = 8.20;
|
|
rubberHoleDepth = 8.92;
|
|
rubberHoleSunkDepth = rubberHoleDepth;
|
|
rubberHoleSunkHeight = 1.5;
|
|
|
|
screwHoleRadius = 3.50/2;
|
|
screwHoleDepthOffset = 4.67 + screwHoleRadius;
|
|
|
|
screwSpikeWidthOffset = 7.10;
|
|
screwSpikeWidth = 2.30;
|
|
screwSpikeDepthOffset = 2.00;
|
|
screwSpikeDepth = 5.5;
|
|
|
|
ledgeGapHeightOffset = 2.80;
|
|
ledgeGapHeight = mountHeight + 0.01 - ledgeGapHeightOffset;//3.18;
|
|
ledgeGapDepth = 5.41;
|
|
ledgeGapWidth = 9.02;
|
|
|
|
handlebarStemRadius = 33.45 / 2;
|
|
handlebarRadius = 32.07 / 2;
|
|
clampRadius = handlebarRadius + 1.5;
|
|
clampInnerRadius = handlebarRadius;
|
|
clampHeightOffset = 3.75;
|
|
clampEndHeightOffset = clampRadius * 1.85;
|
|
|
|
circleResolution=360*2; // faces per rotation
|
|
|
|
difference() {
|
|
union() {
|
|
// mount base
|
|
cube([mountDepth, mountHeight, mountWidth]);
|
|
// circular clamp
|
|
translate([mountDepth/2, clampRadius + clampHeightOffset, mountWidth/2]) {
|
|
rotate([0, 0, 0]) {
|
|
difference() {
|
|
cylinder(h = mountWidth, r = clampRadius, center=true, $fn=circleResolution);
|
|
union() {
|
|
cylinder(h = mountWidth * 1.1, r = clampInnerRadius, center=true, $fn=circleResolution);
|
|
translate([-(clampRadius + 0.01), clampEndHeightOffset - clampRadius, -(mountWidth/2 + 0.01)]) {
|
|
cube([(clampRadius * 2) + 0.02, clampRadius * 2.02, mountWidth + 0.02]);
|
|
}
|
|
}
|
|
}
|
|
}
|
|
}
|
|
}
|
|
union() {
|
|
// hole for rubber grip to clip in
|
|
translate([(mountDepth/2)-(rubberHoleDepth/2), -0.01, (mountWidth/2) - (rubberHoleWidth/2)]) {
|
|
cube([rubberHoleDepth, 10, rubberHoleWidth]);
|
|
}
|
|
// slightly larger hole so rubber grip clip can clip
|
|
translate([(mountDepth/2)-(rubberHoleSunkDepth/2), -0.01, (mountWidth/2) - (rubberHoleSunkWidth/2)]) {
|
|
cube([rubberHoleSunkDepth, mountHeight- rubberHoleSunkHeight, rubberHoleSunkWidth]);
|
|
}
|
|
// screw hole
|
|
translate([screwHoleDepthOffset, -0.01, (mountWidth/2)]) {
|
|
rotate([-90,0,0]) {
|
|
cylinder(h = mountHeight + 0.02, r = screwHoleRadius, $fn=circleResolution);
|
|
}
|
|
}
|
|
// lower hole for spikes on each side of screw
|
|
translate([screwSpikeDepthOffset, -0.01, screwSpikeWidthOffset]) {
|
|
cube([screwSpikeDepth, 5, screwSpikeWidth]);
|
|
}
|
|
// higher hole for spikes on each side of screw
|
|
translate([screwSpikeDepthOffset, -0.01, mountWidth - (screwSpikeWidth + screwSpikeWidthOffset)]) {
|
|
cube([screwSpikeDepth, 5, screwSpikeWidth]);
|
|
}
|
|
// lower ledge at x-axis high end for dial's clip
|
|
translate([mountDepth - ledgeGapDepth, ledgeGapHeightOffset, -0.01]) {
|
|
cube([ledgeGapDepth + 0.01, ledgeGapHeight, ledgeGapWidth + 0.01]);
|
|
}
|
|
// higher ledge at x-axis high end for dial's clip
|
|
translate([mountDepth - ledgeGapDepth, ledgeGapHeightOffset, mountWidth + 0.01 -ledgeGapWidth]) {
|
|
cube([ledgeGapDepth + 0.01, ledgeGapHeight, ledgeGapWidth + 0.01]);
|
|
}
|
|
}
|
|
} |