mirrors/Atmosphere
1
0
Fork 0
mirror of https://github.com/Atmosphere-NX/Atmosphere.git synced 2024-11-26 05:42:17 +00:00
Code Issues Releases Activity

Fix race conditions and misconfiguration in sdmmc

Browse source 
Properly configure pull up and pull down offsets for autocal.
Run autocal prior to every transfer.

Prevent race conditions in sdmmc_wait_for_event() - make sure the fault
handler has highest priority, then the target irq, state conditions and
finally the error mask.

Do not clear all bits (|=) when acknowledging fault conditions,
only acknowledge the fault conditions itself.

Enable interrupts before preparing command registers - if sdmmc is fast
enough it can actually finish transfer before we enabled the interrupts.
Enabling interrupts clears the COMMAND COMPLETE status bit.

Temporarily print all the sdmmc messages in stage2 - for yet unknown
reason respecting the log level results in some failures.

This results in working microsd card in stage2 on my switch with Samsung
EVO+ 256GB microsd card.
This commit is contained in:
Tomasz Moń 2018-06-09 08:44:05 +02:00
parent 7b9dcd2f1a
commit 804a40830e
2 changed files with 82 additions and 48 deletions
Show stats Download patch file Download diff file Expand all files Collapse all files

62
fusee/fusee-primary/src/sdmmc.c
View file

@ -910,32 +910,38 @@ static int sdmmc_set_up_clocking_parameters(struct mmc *mmc, enum sdmmc_bus_volt
{
// Clear the I/O conditioning constants.
mmc->regs->vendor_clock_cntrl &= ~(MMC_CLOCK_TRIM_MASK | MMC_CLOCK_TAP_MASK);
mmc->regs->auto_cal_config &= ~MMC_AUTOCAL_PDPU_CONFIG_MASK;
// Per the TRM, set the PADPIPE clock enable.
mmc->regs->vendor_clock_cntrl |= MMC_CLOCK_PADPIPE_CLKEN_OVERRIDE;
switch (operating_voltage) {
case MMC_VOLTAGE_1V8:
mmc->regs->auto_cal_config |= MMC_AUTOCAL_PDPU_SDMMC4_1V8;
break;
case MMC_VOLTAGE_3V3:
mmc->regs->auto_cal_config |= MMC_AUTOCAL_PDPU_SDMMC1_3V3;
break;
default:
printk("ERROR: currently no controllers support voltage %d", mmc->operating_voltage);
return EINVAL;
}
// Set up the I/O conditioning constants used to ensure we have a reliable clock.
// Constants above and procedure below from the TRM.
switch (mmc->controller) {
case SWITCH_EMMC:
if (operating_voltage != MMC_VOLTAGE_1V8) {
mmc_print(mmc, "ERROR: eMMC can only run at 1V8, but mmc struct claims voltage %d", operating_voltage);
return EINVAL;
}
mmc->regs->auto_cal_config &= ~MMC_AUTOCAL_PDPU_CONFIG_MASK;
mmc->regs->auto_cal_config |= MMC_AUTOCAL_PDPU_SDMMC4_1V8;
mmc->regs->vendor_clock_cntrl |= (MMC_CLOCK_TRIM_SDMMC4 | MMC_CLOCK_TAP_SDMMC4);
break;
case SWITCH_MICROSD:
switch (operating_voltage) {
case MMC_VOLTAGE_1V8:
mmc->regs->auto_cal_config &= ~MMC_AUTOCAL_PDPU_CONFIG_MASK;
mmc->regs->auto_cal_config |= MMC_AUTOCAL_PDPU_SDMMC1_1V8;
break;
case MMC_VOLTAGE_3V3:
mmc->regs->auto_cal_config &= ~MMC_AUTOCAL_PDPU_CONFIG_MASK;
mmc->regs->auto_cal_config |= MMC_AUTOCAL_PDPU_SDMMC1_3V3;
break;
default:
mmc_print(mmc, "ERROR: microsd does not support voltage %d", operating_voltage);
return EINVAL;
}
mmc->regs->vendor_clock_cntrl |= (MMC_CLOCK_TRIM_SDMMC1 | MMC_CLOCK_TAP_SDMMC1);
break;
@ -1756,6 +1762,7 @@ static int sdmmc_wait_for_event(struct mmc *mmc,
uint32_t fault_conditions, fault_handler_t fault_handler)
{
uint32_t timebase = get_time();
uint32_t intstatus;
int rc;
// Wait until we either wind up ready, or until we've timed out.
@ -1763,7 +1770,13 @@ static int sdmmc_wait_for_event(struct mmc *mmc,
if (get_time_since(timebase) > mmc->timeout)
return ETIMEDOUT;
if (mmc->regs->int_status & fault_conditions) {
// Read intstatus into temporary variable to make sure that the
// priorities are: fault conditions, target irq, errors
// This makes sure that if fault conditions and target irq
// comes nearly at the same time that the fault handler will
// always be called
intstatus = mmc->regs->int_status;
if (intstatus & fault_conditions) {
// If we don't have a handler, fault.
if (!fault_handler) {
@ -1779,22 +1792,23 @@ static int sdmmc_wait_for_event(struct mmc *mmc,
}
// Finally, EOI the relevant interrupt.
mmc->regs->int_status |= fault_conditions;
mmc->regs->int_status = fault_conditions;
intstatus &= ~(fault_conditions);
// Reset the timebase, so it applies to the next
// DMA interval.
timebase = get_time();
}
if (mmc->regs->int_status & target_irq)
if (intstatus & target_irq)
return 0;
if (state_conditions && !(mmc->regs->present_state & state_conditions))
return 0;
// If an error occurs, return it.
if (mmc->regs->int_status & MMC_STATUS_ERROR_MASK)
return (mmc->regs->int_status & MMC_STATUS_ERROR_MASK);
if (intstatus & MMC_STATUS_ERROR_MASK)
return (intstatus & MMC_STATUS_ERROR_MASK);
}
}
@ -2042,7 +2056,7 @@ static void sdmmc_enable_interrupts(struct mmc *mmc, bool enabled)
MMC_STATUS_DMA_INTERRUPT | MMC_STATUS_ERROR_MASK;
// Clear any pending interrupts.
mmc->regs->int_status |= all_interrupts;
mmc->regs->int_status = all_interrupts;
// And enable or disable the pseudo-interrupts.
if (enabled) {
@ -2160,6 +2174,8 @@ static int sdmmc_send_command(struct mmc *mmc, enum sdmmc_command command,
}
}
sdmmc_run_autocal(mmc, true);
// If we have data to send, prepare it.
sdmmc_prepare_command_data(mmc, blocks_to_transfer, is_write, auto_terminate, mmc->use_dma, argument);
@ -2168,12 +2184,12 @@ static int sdmmc_send_command(struct mmc *mmc, enum sdmmc_command command,
if (blocks_to_transfer && is_write && mmc->use_dma && data_buffer)
memcpy(sdmmc_bounce_buffer, (void *)mmc->active_data_buffer, total_data_to_xfer);
// Configure the controller to send the command.
sdmmc_prepare_command_registers(mmc, blocks_to_transfer, command, response_type, checks);
// Ensure we get the status response we want.
sdmmc_enable_interrupts(mmc, true);
// Configure the controller to send the command.
sdmmc_prepare_command_registers(mmc, blocks_to_transfer, command, response_type, checks);
// Wait for the command to be completed.
rc = sdmmc_wait_for_command_completion(mmc);
if (rc) {

68
fusee/fusee-secondary/src/sdmmc.c
View file

@ -650,8 +650,10 @@ int sdmmc_set_loglevel(int loglevel)
static void mmc_vprint(struct mmc *mmc, char *fmt, int required_loglevel, va_list list)
{
// Allow debug prints to be silenced by a negative loglevel.
if (sdmmc_loglevel < required_loglevel)
return;
//TODO: respect the log level, most likely there are still some timing problems
//which make it not working when the logging is supressed
//if (sdmmc_loglevel < required_loglevel)
// return;
printk("%s: ", mmc->name);
vprintk(fmt, list);
@ -910,32 +912,38 @@ static int sdmmc_set_up_clocking_parameters(struct mmc *mmc, enum sdmmc_bus_volt
{
// Clear the I/O conditioning constants.
mmc->regs->vendor_clock_cntrl &= ~(MMC_CLOCK_TRIM_MASK | MMC_CLOCK_TAP_MASK);
mmc->regs->auto_cal_config &= ~MMC_AUTOCAL_PDPU_CONFIG_MASK;
// Per the TRM, set the PADPIPE clock enable.
mmc->regs->vendor_clock_cntrl |= MMC_CLOCK_PADPIPE_CLKEN_OVERRIDE;
switch (operating_voltage) {
case MMC_VOLTAGE_1V8:
mmc->regs->auto_cal_config |= MMC_AUTOCAL_PDPU_SDMMC4_1V8;
break;
case MMC_VOLTAGE_3V3:
mmc->regs->auto_cal_config |= MMC_AUTOCAL_PDPU_SDMMC1_3V3;
break;
default:
printk("ERROR: currently no controllers support voltage %d", mmc->operating_voltage);
return EINVAL;
}
// Set up the I/O conditioning constants used to ensure we have a reliable clock.
// Constants above and procedure below from the TRM.
switch (mmc->controller) {
case SWITCH_EMMC:
if (operating_voltage != MMC_VOLTAGE_1V8) {
mmc_print(mmc, "ERROR: eMMC can only run at 1V8, but mmc struct claims voltage %d", operating_voltage);
return EINVAL;
}
mmc->regs->auto_cal_config &= ~MMC_AUTOCAL_PDPU_CONFIG_MASK;
mmc->regs->auto_cal_config |= MMC_AUTOCAL_PDPU_SDMMC4_1V8;
mmc->regs->vendor_clock_cntrl |= (MMC_CLOCK_TRIM_SDMMC4 | MMC_CLOCK_TAP_SDMMC4);
break;
case SWITCH_MICROSD:
switch (operating_voltage) {
case MMC_VOLTAGE_1V8:
mmc->regs->auto_cal_config &= ~MMC_AUTOCAL_PDPU_CONFIG_MASK;
mmc->regs->auto_cal_config |= MMC_AUTOCAL_PDPU_SDMMC1_1V8;
break;
case MMC_VOLTAGE_3V3:
mmc->regs->auto_cal_config &= ~MMC_AUTOCAL_PDPU_CONFIG_MASK;
mmc->regs->auto_cal_config |= MMC_AUTOCAL_PDPU_SDMMC1_3V3;
break;
default:
mmc_print(mmc, "ERROR: microsd does not support voltage %d", operating_voltage);
return EINVAL;
}
mmc->regs->vendor_clock_cntrl |= (MMC_CLOCK_TRIM_SDMMC1 | MMC_CLOCK_TAP_SDMMC1);
break;
@ -1756,6 +1764,7 @@ static int sdmmc_wait_for_event(struct mmc *mmc,
uint32_t fault_conditions, fault_handler_t fault_handler)
{
uint32_t timebase = get_time();
uint32_t intstatus;
int rc;
// Wait until we either wind up ready, or until we've timed out.
@ -1763,7 +1772,13 @@ static int sdmmc_wait_for_event(struct mmc *mmc,
if (get_time_since(timebase) > mmc->timeout)
return ETIMEDOUT;
if (mmc->regs->int_status & fault_conditions) {
// Read intstatus into temporary variable to make sure that the
// priorities are: fault conditions, target irq, errors
// This makes sure that if fault conditions and target irq
// comes nearly at the same time that the fault handler will
// always be called
intstatus = mmc->regs->int_status;
if (intstatus & fault_conditions) {
// If we don't have a handler, fault.
if (!fault_handler) {
@ -1779,22 +1794,23 @@ static int sdmmc_wait_for_event(struct mmc *mmc,
}
// Finally, EOI the relevant interrupt.
mmc->regs->int_status |= fault_conditions;
mmc->regs->int_status = fault_conditions;
intstatus &= ~(fault_conditions);
// Reset the timebase, so it applies to the next
// DMA interval.
timebase = get_time();
}
if (mmc->regs->int_status & target_irq)
if (intstatus & target_irq)
return 0;
if (state_conditions && !(mmc->regs->present_state & state_conditions))
return 0;
// If an error occurs, return it.
if (mmc->regs->int_status & MMC_STATUS_ERROR_MASK)
return (mmc->regs->int_status & MMC_STATUS_ERROR_MASK);
if (intstatus & MMC_STATUS_ERROR_MASK)
return (intstatus & MMC_STATUS_ERROR_MASK);
}
}
@ -2042,7 +2058,7 @@ static void sdmmc_enable_interrupts(struct mmc *mmc, bool enabled)
MMC_STATUS_DMA_INTERRUPT | MMC_STATUS_ERROR_MASK;
// Clear any pending interrupts.
mmc->regs->int_status |= all_interrupts;
mmc->regs->int_status = all_interrupts;
// And enable or disable the pseudo-interrupts.
if (enabled) {
@ -2160,6 +2176,8 @@ static int sdmmc_send_command(struct mmc *mmc, enum sdmmc_command command,
}
}
sdmmc_run_autocal(mmc, true);
// If we have data to send, prepare it.
sdmmc_prepare_command_data(mmc, blocks_to_transfer, is_write, auto_terminate, mmc->use_dma, argument);
@ -2168,12 +2186,12 @@ static int sdmmc_send_command(struct mmc *mmc, enum sdmmc_command command,
if (blocks_to_transfer && is_write && mmc->use_dma && data_buffer)
memcpy(sdmmc_bounce_buffer, (void *)mmc->active_data_buffer, total_data_to_xfer);
// Configure the controller to send the command.
sdmmc_prepare_command_registers(mmc, blocks_to_transfer, command, response_type, checks);
// Ensure we get the status response we want.
sdmmc_enable_interrupts(mmc, true);
// Configure the controller to send the command.
sdmmc_prepare_command_registers(mmc, blocks_to_transfer, command, response_type, checks);
// Wait for the command to be completed.
rc = sdmmc_wait_for_command_completion(mmc);
if (rc) {