/* * Enhanced USB (EHCI) Device driver for Tegra X1 * * Copyright (c) 2019-2020 CTCaer * * This program is free software; you can redistribute it and/or modify it * under the terms and conditions of the GNU General Public License, * version 2, as published by the Free Software Foundation. * * This program is distributed in the hope it will be useful, but WITHOUT * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for * more details. * * You should have received a copy of the GNU General Public License * along with this program. If not, see . */ #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include typedef enum { USB_HW_EP0 = 0, USB_HW_EP1 = 1 } usb_hw_ep_t; typedef enum { USB_EP_STATUS_IDLE = 0, USB_EP_STATUS_ACTIVE = 1, USB_EP_STATUS_ERROR = 2, USB_EP_STATUS_NO_CONFIG = 3, USB_EP_STATUS_STALLED = 4, USB_EP_STATUS_DISABLED = 5 } usb_ep_status_t; typedef enum { USB_LOW_SPEED = 0, USB_FULL_SPEED = 1, USB_HIGH_SPEED = 2, USB_SUPER_SPEED = 3, } usb_speed_t; typedef struct _dTD_t { vu32 next_dTD; vu32 info; vu32 pages[5]; vu32 reserved; } dTD_t; typedef struct _dQH_t { vu32 ep_capabilities; vu32 curr_dTD_ptr; vu32 next_dTD_ptr; vu32 token; vu32 buffers[5]; // hmmm. vu32 reserved; vu32 setup[2]; vu32 gap[4]; } dQH_t; typedef struct _usbd_t { volatile dTD_t dtds[4 * 4]; // 4 dTD per endpoint. volatile dQH_t *qhs; int ep_configured[4]; int ep_bytes_requested[4]; } usbd_t; typedef struct _usbd_controller_t { u32 port_speed; t210_usb2d_t *regs; usb_ctrl_setup_t control_setup; usb_desc_t *desc; usb_gadget_type type; u8 configuration_set; u8 usb_phy_ready; u8 configuration; u8 interface; u8 max_lun; u8 max_lun_set; u8 bulk_reset_req; u8 hid_report_sent; bool charger_detect; } usbd_controller_t; extern u8 hid_report_descriptor_jc[]; extern u8 hid_report_descriptor_touch[]; extern u32 hid_report_descriptor_jc_size; extern u32 hid_report_descriptor_touch_size; extern usb_desc_t usb_gadget_hid_jc_descriptors; extern usb_desc_t usb_gadget_hid_touch_descriptors; extern usb_desc_t usb_gadget_ums_descriptors; usbd_t *usbdaemon; usbd_controller_t *usbd_otg; usbd_controller_t usbd_usb_otg_controller_ctxt; bool usb_init_done = false; u8 *usb_ep0_ctrl_buf = (u8 *)USB_EP_CONTROL_BUF_ADDR; static int _usbd_reset_usb_otg_phy_device_mode() { usbd_otg->usb_phy_ready = 0; // Clear UTMIP reset. USB(USB1_IF_USB_SUSP_CTRL) &= ~SUSP_CTRL_UTMIP_RESET; // Wait for PHY clock to get validated. u32 retries = 100000; // 200ms timeout. while (!(USB(USB1_IF_USB_SUSP_CTRL) & SUSP_CTRL_USB_PHY_CLK_VALID)) { retries--; if (!retries) return 1; usleep(1); } usbd_otg->usb_phy_ready = 1; // Clear all device addresses, enabled setup requests and transmit events. usbd_otg->regs->periodiclistbase = 0; usbd_otg->regs->endptsetupstat = usbd_otg->regs->endptsetupstat; usbd_otg->regs->endptcomplete = usbd_otg->regs->endptcomplete; // Stop device controller. usbd_otg->regs->usbcmd &= ~USB2D_USBCMD_RUN; // Set controller mode to idle. usbd_otg->regs->usbmode &= ~USB2D_USBMODE_CM_MASK; // Reset the controller. usbd_otg->regs->usbcmd |= USB2D_USBCMD_RESET; // Wait for the reset to complete. retries = 100000; // 200ms timeout. while (usbd_otg->regs->usbcmd & USB2D_USBCMD_RESET) { retries--; if (!retries) return 2; usleep(1); } // Wait for PHY clock to get validated after reset. retries = 100000; // 200ms timeout. while (!(USB(USB1_IF_USB_SUSP_CTRL) & SUSP_CTRL_USB_PHY_CLK_VALID)) { retries--; if (!retries) return 3; usleep(1); } // Set controller to Device mode. usbd_otg->regs->usbmode = (usbd_otg->regs->usbmode & ~USB2D_USBMODE_CM_MASK) | USB2D_USBMODE_CM_DEVICE; // Wait for the selected mode to be enabled. retries = 100000; // 200ms timeout. while ((usbd_otg->regs->usbmode & USB2D_USBMODE_CM_MASK) != USB2D_USBMODE_CM_DEVICE) { retries--; if (!retries) return 4; usleep(1); } // Disable all interrupts. usbd_otg->regs->usbintr = 0; // Set the ID pullup and disable all OTGSC interrupts. usbd_otg->regs->otgsc = USB2D_OTGSC_USB_ID_PULLUP; // Clear all relevant interrupt statuses. usbd_otg->regs->usbsts = USB2D_USBSTS_UI | USB2D_USBSTS_UEI | USB2D_USBSTS_PCI | USB2D_USBSTS_FRI | USB2D_USBSTS_SEI | USB2D_USBSTS_AAI | USB2D_USBSTS_URI | USB2D_USBSTS_SRI | USB2D_USBSTS_SLI; // Disable and clear all OTGSC interrupts. usbd_otg->regs->otgsc = USB2D_OTGSC_USB_IRQ_STS_MASK; // Clear EP0, EP1, EP2 setup requests. usbd_otg->regs->endptsetupstat = 7; //TODO: Shouldn't this be endptsetupstat = endptsetupstat? // Set all interrupts to immediate. usbd_otg->regs->usbcmd &= ~USB2D_USBCMD_ITC_MASK; return 0; } static void _usb_charger_detect() { // Charger detect init. usbd_otg->charger_detect = 0; bool charger_detect_enable = FUSE(FUSE_RESERVED_SW) & 0x10; // Disabled on Switch production. if (charger_detect_enable) { usbd_otg->charger_detect |= 1; // Configure detect pin. PINMUX_AUX(PINMUX_AUX_LCD_GPIO1) &= ~(PINMUX_PARKED | PINMUX_TRISTATE | PINMUX_PULL_MASK); gpio_config(GPIO_PORT_V, GPIO_PIN_3, GPIO_MODE_GPIO); // Configure charger pin. PINMUX_AUX(PINMUX_AUX_USB_VBUS_EN1) &= ~(PINMUX_INPUT_ENABLE | PINMUX_PARKED | PINMUX_TRISTATE | PINMUX_PULL_MASK); gpio_config(GPIO_PORT_CC, GPIO_PIN_5, GPIO_MODE_GPIO); gpio_output_enable(GPIO_PORT_CC, GPIO_PIN_5, GPIO_OUTPUT_ENABLE); // Enable charger. if (gpio_read(GPIO_PORT_V, GPIO_PIN_3)) { usbd_otg->charger_detect |= 2; gpio_write(GPIO_PORT_CC, GPIO_PIN_5, GPIO_HIGH); usbd_otg->charger_detect |= 0x100; USB(USB1_UTMIP_BAT_CHRG_CFG0) = BAT_CHRG_CFG0_OP_SRC_EN; // Clears UTMIP_PD_CHRG and enables charger detect. usleep(5000); } } } int usb_device_init() { if (usb_init_done) return 0; // Configure PLLU. CLOCK(CLK_RST_CONTROLLER_PLLU_MISC) |= (1 << 29); // Disable reference clock. u32 pllu_cfg = (((((CLOCK(CLK_RST_CONTROLLER_PLLU_BASE) >> 8 << 8) | 2) & 0xFFFF00FF) | ((0x19 << 8) & 0xFFFF)) & 0xFFE0FFFF) | (1 << 16) | (1 << 24); CLOCK(CLK_RST_CONTROLLER_PLLU_BASE) = pllu_cfg; CLOCK(CLK_RST_CONTROLLER_PLLU_BASE) = pllu_cfg | (1 << 30); // Enable. // Wait for PLL to stabilize. u32 timeout = (u32)TMR(TIMERUS_CNTR_1US) + 1300; while (!(CLOCK(CLK_RST_CONTROLLER_PLLU_BASE) & (1 << 27))) // PLL_LOCK. if ((u32)TMR(TIMERUS_CNTR_1US) > timeout) break; usleep(10); // Enable PLLU USB/HSIC/ICUSB/48M. CLOCK(CLK_RST_CONTROLLER_PLLU_BASE) |= 0x2E00000; // Enable USBD clock. CLOCK(CLK_RST_CONTROLLER_CLK_ENB_L_SET) = BIT(CLK_L_USBD); usleep(2); CLOCK(CLK_RST_CONTROLLER_RST_DEV_L_SET) = BIT(CLK_L_USBD); usleep(2); CLOCK(CLK_RST_CONTROLLER_RST_DEV_L_CLR) = BIT(CLK_L_USBD); usleep(2); // Clear XUSB_PADCTL reset CLOCK(CLK_RST_CONTROLLER_RST_DEV_W_CLR) = BIT(CLK_W_XUSB_PADCTL); // Enable USB PHY and reset for programming. u32 usb_susp_ctrl = USB(USB1_IF_USB_SUSP_CTRL); USB(USB1_IF_USB_SUSP_CTRL) = usb_susp_ctrl | SUSP_CTRL_UTMIP_RESET; USB(USB1_IF_USB_SUSP_CTRL) = usb_susp_ctrl | SUSP_CTRL_UTMIP_PHY_ENB | SUSP_CTRL_UTMIP_RESET; // Disable UTMIPLL IDDQ. CLOCK(CLK_RST_CONTROLLER_UTMIPLL_HW_PWRDN_CFG0) &= 0xFFFFFFFD; usleep(10); // Disable crystal clock. USB(USB1_UTMIP_MISC_CFG1) &= 0xBFFFFFFF; CLOCK(CLK_RST_CONTROLLER_UTMIP_PLL_CFG2) &= 0xBFFFFFFF; // Set B_SESS_VLD. USB(USB1_IF_USB_PHY_VBUS_SENSORS) |= 0x1000; USB(USB1_IF_USB_PHY_VBUS_SENSORS) |= 0x800; // Set UTMIPLL dividers and enable it. CLOCK(CLK_RST_CONTROLLER_UTMIP_PLL_CFG0) = (CLOCK(CLK_RST_CONTROLLER_UTMIP_PLL_CFG0) & 0xFF0000FF) | 0x190000 | 0x100; CLOCK(CLK_RST_CONTROLLER_UTMIP_PLL_CFG2) = (CLOCK(CLK_RST_CONTROLLER_UTMIP_PLL_CFG2) & 0xFF00003F) | 0x600000; // Set delay count for 38.4Mhz osc crystal. CLOCK(CLK_RST_CONTROLLER_UTMIP_PLL_CFG1) = ((CLOCK(CLK_RST_CONTROLLER_UTMIP_PLL_CFG1) & 0x7FFF000) | 0x8000 | 0x177) & 0xFFFFAFFF; // Wait for UTMIPLL to stabilize. u32 retries = 10; // Wait 20us while (!(CLOCK(CLK_RST_CONTROLLER_UTMIPLL_HW_PWRDN_CFG0) & 0x80000000) && retries) { usleep(1); retries--; } // Configure UTMIP Transceiver Cells. u32 fuse_usb_calib = FUSE(FUSE_USB_CALIB); USB(USB1_UTMIP_XCVR_CFG0) = (((USB(USB1_UTMIP_XCVR_CFG0) & 0xFFFFFFF0) | (fuse_usb_calib & 0xF)) & 0xFE3FFFFF) | ((fuse_usb_calib & 0x3F) << 25 >> 29 << 22); USB(USB1_UTMIP_XCVR_CFG1) = (USB(USB1_UTMIP_XCVR_CFG1) & 0xFFC3FFFF) | ((fuse_usb_calib << 21) >> 28 << 18); USB(USB1_UTMIP_XCVR_CFG3) = (USB(USB1_UTMIP_XCVR_CFG3) & 0xFFFFC1FF) | ((FUSE(FUSE_USB_CALIB_EXT) & 0x1F) << 9); USB(USB1_UTMIP_XCVR_CFG0) &= 0xFFDFFFFF; USB(USB1_UTMIP_XCVR_CFG2) = (USB(USB1_UTMIP_XCVR_CFG2) & 0xFFFFF1FF) | 0x400; usleep(1); // Configure misc UTMIP. USB(USB1_UTMIP_DEBOUNCE_CFG0) = (USB(USB1_UTMIP_DEBOUNCE_CFG0) & 0xFFFF0000) | 0xBB80; USB(USB1_UTMIP_BIAS_CFG1) = (USB(USB1_UTMIP_BIAS_CFG1) & 0xFFFFC0FF) | 0x100; // when osc is 38.4KHz //USB(USB1_UTMIP_SPARE_CFG0) &= 0xFFFFFEE7; unpatched0 USB(USB1_UTMIP_BIAS_CFG2) |= 2; //patched0 - UTMIP_HSSQUELCH_LEVEL_NEW: 2. USB(USB1_UTMIP_SPARE_CFG0) &= 0xFFFFFE67; //patched0 - FUSE_HS_IREF_CAP_CFG USB(USB1_UTMIP_TX_CFG0) |= 0x80000; //USB(USB1_UTMIP_HSRX_CFG0) = (USB(USB1_UTMIP_HSRX_CFG0) & 0xFFF003FF) | 0x88000 | 0x4000; unpatched1 USB(USB1_UTMIP_HSRX_CFG0) = (USB(USB1_UTMIP_HSRX_CFG0) & 0xF0F003FF) | 0x88000 | 0x4000; //patched1 - reset UTMIP_PCOUNT_UPDN_DIV: From 1 to 0. USB(USB1_UTMIP_BIAS_CFG2) &= 0xFFFFFFF8; //patched1 - UTMIP_HSSQUELCH_LEVEL_NEW: 0 USB(USB1_UTMIP_HSRX_CFG1) = (USB(USB1_UTMIP_HSRX_CFG1) & 0xFFFFFFC1) | 0x12; USB(USB1_UTMIP_MISC_CFG1) |= 0x40000000; // Enable crystal clock. CLOCK(CLK_RST_CONTROLLER_UTMIP_PLL_CFG2) |= 0x40000000; // Enable USB2 tracking. CLOCK(CLK_RST_CONTROLLER_CLK_ENB_Y_SET) = BIT(CLK_Y_USB2_TRK); CLOCK(CLK_RST_CONTROLLER_CLK_SOURCE_USB2_HSIC_TRK) = (CLOCK(CLK_RST_CONTROLLER_CLK_SOURCE_USB2_HSIC_TRK) & 0xFFFFFF00) | 6; // Set trank divisor to 4. USB(USB1_UTMIP_BIAS_CFG1) = (USB(USB1_UTMIP_BIAS_CFG1) & 0xFFC03F07) | 0x78000 | 0x50; // Set delays. USB(USB1_UTMIP_BIAS_CFG0) &= 0xFFFFFBFF; // Disable Power down bias circuit. usleep(1); // Force PDTRK input into power up. USB(USB1_UTMIP_BIAS_CFG1) = (USB(USB1_UTMIP_BIAS_CFG1) & 0xFFFFFFFE) | 2; usleep(100); // TRK cycle done. Force PDTRK input into power down. USB(USB1_UTMIP_BIAS_CFG1) = (USB(USB1_UTMIP_BIAS_CFG1) & 0xFF7FFFFF) | 1; usleep(3); // Force PDTRK input into power up. USB(USB1_UTMIP_BIAS_CFG1) = USB(USB1_UTMIP_BIAS_CFG1) & 0xFFFFFFFE; usleep(100); // TRK cycle done. Force PDTRK input into power down. USB(USB1_UTMIP_BIAS_CFG1) = (USB(USB1_UTMIP_BIAS_CFG1) & 0xFF7FFFFF) | 1; // Disable USB2_TRK clock and configure UTMIP misc. CLOCK(CLK_RST_CONTROLLER_CLK_ENB_Y_CLR) = BIT(CLK_Y_USB2_TRK); CLOCK(CLK_RST_CONTROLLER_UTMIP_PLL_CFG2) = (CLOCK(CLK_RST_CONTROLLER_UTMIP_PLL_CFG2) & 0xFEFFFFEA) | 0x2000000 | 0x28 | 2; usleep(1); USB(USB1_UTMIP_BIAS_CFG0) &= 0xFF3FF7FF; usleep(1); // Clear power downs on UTMIP ID and VBUS wake up, PD, PD2, PDZI, PDCHRP, PDDR. PMC(APBDEV_PMC_USB_AO) &= 0xFFFFFFF3; // UTMIP ID and VBUS wake up. usleep(1); USB(USB1_UTMIP_XCVR_CFG0) &= 0xFFFFBFFF; // UTMIP_FORCE_PD_POWERDOWN. usleep(1); USB(USB1_UTMIP_XCVR_CFG0) &= 0xFFFEFFFF; // UTMIP_FORCE_PD2_POWERDOWN. usleep(1); USB(USB1_UTMIP_XCVR_CFG0) &= 0xFFFBFFFF; // UTMIP_FORCE_PDZI_POWERDOWN. usleep(1); USB(USB1_UTMIP_XCVR_CFG1) &= 0xFFFFFFFB; // UTMIP_FORCE_PDCHRP_POWERDOWN. usleep(1); USB(USB1_UTMIP_XCVR_CFG1) &= 0xFFFFFFEF; // UTMIP_FORCE_PDDR_POWERDOWN. usleep(1); // AHB USB performance cfg. AHB_GIZMO(AHB_GIZMO_AHB_MEM) |= AHB_MEM_ENB_FAST_REARBITRATE; AHB_GIZMO(AHB_GIZMO_USB) |= AHB_GIZMO_USB_IMMEDIATE; AHB_GIZMO(AHB_ARBITRATION_PRIORITY_CTRL) |= ARBITRATION_PRIORITY_CTRL_ENB_FAST_REARBITRATE; AHB_GIZMO(AHB_AHB_MEM_PREFETCH_CFG1) = MEM_PREFETCH_ENABLE | (MEM_PREFETCH_AHB_MST_USB << 26) | (12 << 21) | 0x1000; // addr boundary 64KB // Set software and hardware context storage and clear it. usbdaemon = (usbd_t *)USBD_ADDR; // Depends on USB_TD_BUFFER_PAGE_SIZE aligned address. usbd_otg = &usbd_usb_otg_controller_ctxt; memset(usbd_otg, 0, sizeof(usbd_controller_t)); memset(usbdaemon, 0, sizeof(usbd_t)); usbd_otg->regs = (t210_usb2d_t *)USB_OTG_BASE; usbd_otg->usb_phy_ready = 0; // Initialize USB PHY on the USB_OTG Controller (#1) in Device mode. int result = _usbd_reset_usb_otg_phy_device_mode(); usbd_otg->configuration_set = 0; _usb_charger_detect(); if (!result) usb_init_done = true; return result; } static void _usb_device_power_down() { // Enable PHY low power suspend. usbd_otg->regs->hostpc1_devlc |= USB2D_HOSTPC1_DEVLC_PHCD; // Do not use any controller regs after the above! // A reset or clear of the PHCD suspend bit must happen. // Power down OTG and Bias circuits. USB(USB1_UTMIP_BIAS_CFG0) |= (1 << 11) | (1 << 10); // UTMIP_OTGPD, UTMIP_BIASPD. // Power down ID detectors. USB(USB1_UTMIP_BIAS_CFG0) |= (1 << 23) | (1 << 22); //UTMIP_IDPD_SEL, UTMIP_IDPD_VAL. if (usbd_otg->charger_detect) { USB(USB1_UTMIP_BAT_CHRG_CFG0) = 1; //UTMIP_PD_CHRG usbd_otg->charger_detect = 0; } // Power down the UTMIP transceivers. // UTMIP_FORCE_PDZI_POWERDOWN, UTMIP_FORCE_PD2_POWERDOWN, UTMIP_FORCE_PD_POWERDOWN. USB(USB1_UTMIP_XCVR_CFG0) |= (1 << 18) | (1 << 16) |(1 << 14); // UTMIP_FORCE_PDDR_POWERDOWN, UTMIP_FORCE_PDCHRP_POWERDOWN, UTMIP_FORCE_PDDISC_POWERDOWN. USB(USB1_UTMIP_XCVR_CFG1) |= (1 << 4) | (1 << 2) | (1 << 0); // Keep UTMIP in reset. USB(USB1_IF_USB_SUSP_CTRL) |= SUSP_CTRL_UTMIP_RESET; // Power down PD trunk. USB(USB1_UTMIP_BIAS_CFG1) |= (1 << 0); //UTMIP_FORCE_PDTRK_POWERDOWN. // Force UTMIP_PLL power down. CLOCK(CLK_RST_CONTROLLER_UTMIP_PLL_CFG1) |= (1 << 14); // UTMIP_FORCE_PLL_ENABLE_POWERDOWN. CLOCK(CLK_RST_CONTROLLER_UTMIP_PLL_CFG1) |= (1 << 12); // UTMIP_FORCE_PLL_ACTIVE_POWERDOWN. CLOCK(CLK_RST_CONTROLLER_UTMIP_PLL_CFG2) |= (1 << 4) | (1 << 0); // UTMIP_FORCE_PD_SAMP_A/C_POWERDOWN. CLOCK(CLK_RST_CONTROLLER_UTMIP_PLL_CFG1) |= (1 << 16); // UTMIP_FORCE_PLLU_POWERDOWN. // Disable crystal clock. USB(USB1_UTMIP_MISC_CFG1) &= 0xBFFFFFFF; // Enable UTMIPLL IDDQ. CLOCK(CLK_RST_CONTROLLER_UTMIPLL_HW_PWRDN_CFG0) |= 2; // Set XUSB_PADCTL reset CLOCK(CLK_RST_CONTROLLER_RST_DEV_W_SET) = BIT(CLK_W_XUSB_PADCTL); // Disable USBD clock. CLOCK(CLK_RST_CONTROLLER_CLK_ENB_L_CLR) = BIT(CLK_L_USBD); // Completely disable PLLU. CLOCK(CLK_RST_CONTROLLER_PLLU_BASE) &= ~0x2E00000; // Disable PLLU USB/HSIC/ICUSB/48M. CLOCK(CLK_RST_CONTROLLER_PLLU_BASE) &= ~0x40000000; // Disable PLLU. CLOCK(CLK_RST_CONTROLLER_PLLU_MISC) &= ~0x20000000; // Enable reference clock. usb_init_done = false; } static void _usbd_stall_reset_ep1(usb_dir_t direction, usb_ep_cfg_t stall) { stall &= 1; if (direction == USB_DIR_IN) { usbd_otg->regs->endptctrl[1] = (usbd_otg->regs->endptctrl[1] & ~USB2D_ENDPTCTRL_TX_EP_STALL) | ((u32)stall << 16); if (!stall) usbd_otg->regs->endptctrl[1] |= USB2D_ENDPTCTRL_TX_EP_RESET; } else { usbd_otg->regs->endptctrl[1] = (usbd_otg->regs->endptctrl[1] & ~USB2D_ENDPTCTRL_RX_EP_STALL) | stall; if (!stall) usbd_otg->regs->endptctrl[1] |= USB2D_ENDPTCTRL_RX_EP_RESET; } } void usb_device_stall_ep1_bulk_out() { _usbd_stall_reset_ep1(USB_DIR_OUT, USB_EP_CFG_STALL); } void usb_device_stall_ep1_bulk_in() { _usbd_stall_reset_ep1(USB_DIR_IN, USB_EP_CFG_STALL); } int usbd_get_max_pkt_length(int endpoint) { switch (endpoint) { case USB_EP_CTRL_OUT: case USB_EP_CTRL_IN: return 64; case USB_EP_BULK_OUT: case USB_EP_BULK_IN: if (usbd_otg->port_speed == 2) return 512; else return 64; default: return 64; } } static void _usbd_initialize_ep_ctrl(u32 endpoint) { usb_hw_ep_t actual_ep = (endpoint & 2) >> 1; usb_dir_t direction = endpoint & 1; memset((void *)&usbdaemon->qhs[endpoint], 0, sizeof(dQH_t)); if (!endpoint) usbdaemon->qhs[endpoint].ep_capabilities = USB_QHD_EP_CAP_IOS_ENABLE; usbdaemon->qhs[endpoint].next_dTD_ptr = 1; // TERMINATE_SET u32 max_packet_len = usbd_get_max_pkt_length(endpoint) & USB_QHD_EP_CAP_MAX_PKT_LEN_MASK; usbdaemon->qhs[endpoint].ep_capabilities |= max_packet_len << 16; if (direction == USB_DIR_IN) { u32 endpoint_type = usbd_otg->regs->endptctrl[actual_ep] & ~USB2D_ENDPTCTRL_TX_EP_TYPE_MASK; if (actual_ep) endpoint_type |= usbd_otg->type ? USB2D_ENDPTCTRL_TX_EP_TYPE_INTR : USB2D_ENDPTCTRL_TX_EP_TYPE_BULK; else endpoint_type |= USB2D_ENDPTCTRL_TX_EP_TYPE_CTRL; usbd_otg->regs->endptctrl[actual_ep] = endpoint_type; usbd_otg->regs->endptctrl[actual_ep] &= ~USB2D_ENDPTCTRL_TX_EP_STALL; if (actual_ep == USB_HW_EP1) usbd_otg->regs->endptctrl[1] |= USB2D_ENDPTCTRL_TX_EP_RESET; usbd_otg->regs->endptctrl[actual_ep] |= USB2D_ENDPTCTRL_TX_EP_ENABLE; } else // EP Bulk OUT. { u32 endpoint_type = usbd_otg->regs->endptctrl[actual_ep] & ~USB2D_ENDPTCTRL_RX_EP_TYPE_MASK; if (actual_ep) { endpoint_type |= usbd_otg->type ? USB2D_ENDPTCTRL_RX_EP_TYPE_INTR : USB2D_ENDPTCTRL_RX_EP_TYPE_BULK; } else endpoint_type |= USB2D_ENDPTCTRL_RX_EP_TYPE_CTRL; usbd_otg->regs->endptctrl[actual_ep] = endpoint_type; usbd_otg->regs->endptctrl[actual_ep] &= ~USB2D_ENDPTCTRL_RX_EP_STALL; if (actual_ep == USB_HW_EP1) usbd_otg->regs->endptctrl[1] |= USB2D_ENDPTCTRL_RX_EP_RESET; usbd_otg->regs->endptctrl[actual_ep] |= USB2D_ENDPTCTRL_RX_EP_ENABLE; } } static int _usbd_initialize_ep0() { memset((void *)usbdaemon->qhs, 0, sizeof(dQH_t) * 4); // Clear all used EP queue heads. memset((void *)usbdaemon->dtds, 0, sizeof(dTD_t) * 4); // Clear all used EP0 token heads. usbd_otg->regs->asynclistaddr = (u32)usbdaemon->qhs; _usbd_initialize_ep_ctrl(USB_EP_CTRL_OUT); _usbd_initialize_ep_ctrl(USB_EP_CTRL_IN); // Disable Auto Low Power. usbd_otg->regs->hostpc1_devlc &= ~USB2D_HOSTPC1_DEVLC_ASUS; // Initiate an attach event. usbd_otg->regs->usbcmd |= USB2D_USBCMD_RUN; u32 retries = 100000; // 200ms timeout. while (!(usbd_otg->regs->usbcmd & USB2D_USBCMD_RUN)) { retries--; if (!retries) return 3; usleep(1); } return 0; } // static void _disable_usb_wdt4() // { // if (TIMER_WDT4_STATUS & 1)// active // { // TIMER_TMR0_TMR_PTV &= 0x7FFFFFFF; // Disable timer // TIMER_WDT4_UNLOCK_PATTERN = 0xC45A; // Alow writes to disable counter bit. // TIMER_WDT4_COMMAND |= 2; // Disable counter // TIMER_TMR0_TMR_PCR |= 0x40000000;// INTR_CLR // } // } int usbd_flush_endpoint(u32 endpoint) { usb_hw_ep_t actual_ep = (endpoint & 2) >> 1; usb_dir_t direction = endpoint & 1; u32 reg_mask = endpoint; // Flash all endpoints or 1. if (endpoint != USB_EP_ALL) { if (direction == USB_DIR_IN) reg_mask = USB2D_ENDPT_STATUS_TX_OFFSET << actual_ep; else reg_mask = USB2D_ENDPT_STATUS_RX_OFFSET << actual_ep; } usbd_otg->regs->endptflush = reg_mask; u32 retries = 100000; // 200ms timeout. while (usbd_otg->regs->endptflush & reg_mask) { retries--; if (!retries) return 3; usleep(1); } // Wait for the endpoint to finish all transactions (buffer not ready). retries = 100000; // 200ms timeout. while (usbd_otg->regs->endptstatus & reg_mask) { retries--; if (!retries) return 3; usleep(1); } // Wait for the endpoint to clear the primed status. retries = 100000; // 200ms timeout. while (usbd_otg->regs->endptprime & reg_mask) { retries--; if (!retries) return 3; usleep(1); } return 0; } void usbd_end(bool reset_ep, bool only_controller) { if (reset_ep) { usbd_flush_endpoint(USB_EP_ALL); _usbd_stall_reset_ep1(0, USB_EP_CFG_RESET); // EP1 Bulk IN. _usbd_stall_reset_ep1(1, USB_EP_CFG_RESET); // EP1 Bulk OUT. //TODO: what about EP0 simultaneous in/out reset. usbd_otg->configuration = 0; usbd_otg->interface = 0; usbd_otg->configuration_set = false; usbd_otg->max_lun_set = false; } // Stop device controller. usbd_otg->regs->usbcmd &= ~USB2D_USBCMD_RUN; // Enable PHY auto low power suspend. usbd_otg->regs->hostpc1_devlc |= USB2D_HOSTPC1_DEVLC_ASUS; if (!only_controller) _usb_device_power_down(); } static void _usbd_mark_ep_complete(u32 endpoint) { u32 complete_bit; usb_hw_ep_t actual_ep = (endpoint & 2) >> 1; usb_dir_t direction = endpoint & 1; usbd_flush_endpoint(endpoint); memset((void *)&usbdaemon->dtds[endpoint * 4], 0, sizeof(dTD_t) * 4); memset((void *)&usbdaemon->qhs[endpoint], 0, sizeof(dQH_t)); usbdaemon->ep_configured[endpoint] = 0; usbdaemon->ep_bytes_requested[endpoint] = 0; if (direction == USB_DIR_IN) complete_bit = USB2D_ENDPT_STATUS_TX_OFFSET << actual_ep; else complete_bit = USB2D_ENDPT_STATUS_RX_OFFSET << actual_ep; usbd_otg->regs->endptcomplete |= complete_bit; } static usb_ep_status_t _usbd_get_ep_status(usb_ep_t endpoint) { bool status; u32 reg_val; u32 reg_mask; u32 actual_ep = (endpoint & 2) >> 1; usb_dir_t direction = endpoint & 1; if (direction == USB_DIR_IN) reg_mask = USB2D_ENDPT_STATUS_TX_OFFSET << actual_ep; else reg_mask = USB2D_ENDPT_STATUS_RX_OFFSET << actual_ep; if (actual_ep == USB_HW_EP1) reg_val = usbd_otg->regs->endptctrl[1]; else reg_val = usbd_otg->regs->endptctrl[0]; // Check stalled status. if (direction == USB_DIR_IN) status = reg_val & USB2D_ENDPTCTRL_TX_EP_STALL; else status = reg_val & USB2D_ENDPTCTRL_RX_EP_STALL; if (status) return USB_EP_STATUS_STALLED; // Check enabled status. if (direction == USB_DIR_IN) status = reg_val & USB2D_ENDPTCTRL_TX_EP_ENABLE; else status = reg_val & USB2D_ENDPTCTRL_RX_EP_ENABLE; if (!status) return USB_EP_STATUS_DISABLED; // CHeck qHD error status. u32 token_error_mask = USB_QHD_TOKEN_HALTED | USB_QHD_TOKEN_BUFFER_ERROR | USB_QHD_TOKEN_XFER_ERROR; if (usbdaemon->qhs[endpoint].token & token_error_mask) return USB_EP_STATUS_ERROR; // Check if endpoint has a request or a ready buffer. if ((usbd_otg->regs->endptprime & reg_mask) || (usbd_otg->regs->endptstatus & reg_mask)) return USB_EP_STATUS_ACTIVE; // RX/TX active. // Return idle or not configured status. if (!usbdaemon->ep_configured[endpoint]) return USB_EP_STATUS_NO_CONFIG; return USB_EP_STATUS_IDLE; } static int _usbd_ep_operation(usb_ep_t endpoint, u8 *buf, u32 len, bool sync) { if (!buf) len = 0; u32 prime_bit; usb_hw_ep_t actual_ep = (endpoint & 2) >> 1; usb_dir_t direction = endpoint & 1; u32 length_left = len; u32 dtd_ep_idx = endpoint * 4; _usbd_mark_ep_complete(endpoint); if (endpoint == USB_EP_CTRL_OUT) usbdaemon->qhs[endpoint].ep_capabilities = USB_QHD_EP_CAP_IOS_ENABLE; u32 max_packet_len = usbd_get_max_pkt_length(endpoint) & USB_QHD_EP_CAP_MAX_PKT_LEN_MASK; usbdaemon->qhs[endpoint].ep_capabilities |= (max_packet_len << 16) | USB_QHD_EP_CAP_ZERO_LEN_TERM_DIS; usbdaemon->qhs[endpoint].next_dTD_ptr = 0; // Clear terminate bit. //usbdaemon->qhs[endpoint].ep_capabilities |= USB_QHD_TOKEN_IRQ_ON_COMPLETE; usbdaemon->ep_configured[endpoint] = 1; usbdaemon->ep_bytes_requested[endpoint] = len; // Configure dTD. u32 dtd_idx = 0; do { if (dtd_idx) usbdaemon->dtds[dtd_ep_idx + dtd_idx - 1].next_dTD = (u32)&usbdaemon->dtds[dtd_ep_idx + dtd_idx]; u32 dtd_size = MIN(length_left, USB_TD_BUFFER_MAX_SIZE); // 16KB max per dTD. usbdaemon->dtds[dtd_ep_idx + dtd_idx].info = (dtd_size << 16) | USB_QHD_TOKEN_ACTIVE; // usbdaemon->dtds[dtd_ep_idx + dtd_idx].info |= USB_QHD_TOKEN_IRQ_ON_COMPLETE; // Set buffers addresses to all page pointers. u32 dt_buffer_offset = dtd_idx * USB_TD_BUFFER_MAX_SIZE; for (u32 i = 0; i < 4; i++) usbdaemon->dtds[dtd_ep_idx + dtd_idx].pages[i] = (u32)&buf[dt_buffer_offset + (USB_TD_BUFFER_PAGE_SIZE * i)]; //usbdaemon->dtds[dtd_ep_idx + dtd_idx].pages[5] = // (u32)&buf[dt_buffer_offset + (USB_TD_BUFFER_PAGE_SIZE * 4)]; // Last buffer. Unused. length_left -= dtd_size; if (length_left) dtd_idx++; } while (length_left); // Last dTD, terminate it. usbdaemon->dtds[dtd_ep_idx + dtd_idx].next_dTD = 1; // Set first dTD address to queue head next dTD. usbdaemon->qhs[endpoint].next_dTD_ptr |= (u32)&usbdaemon->dtds[dtd_ep_idx] & 0xFFFFFFE0; // Flush AHB prefetcher. AHB_GIZMO(AHB_AHB_MEM_PREFETCH_CFG1) &= ~MEM_PREFETCH_ENABLE; AHB_GIZMO(AHB_AHB_MEM_PREFETCH_CFG1) |= MEM_PREFETCH_ENABLE; if (direction == USB_DIR_IN) { prime_bit = USB2D_ENDPT_STATUS_TX_OFFSET << actual_ep; bpmp_mmu_maintenance(BPMP_MMU_MAINT_CLN_INV_WAY, false); } else prime_bit = USB2D_ENDPT_STATUS_RX_OFFSET << actual_ep; // Prime endpoint. usbd_otg->regs->endptprime |= prime_bit; // USB2_CONTROLLER_USB2D_ENDPTPRIME. int res = 0; usb_ep_status_t ep_status; if (sync) { ep_status = _usbd_get_ep_status(endpoint); if (ep_status == USB_EP_STATUS_ACTIVE) { u32 retries = 1000000; // Timeout 2s. while (retries) { ep_status = _usbd_get_ep_status(endpoint); if (ep_status != USB_EP_STATUS_ACTIVE) { if (ep_status == USB_EP_STATUS_DISABLED) res = 28; goto out; } retries--; usleep(1); } res = 3; } else if (ep_status == USB_EP_STATUS_DISABLED) res = 28; out: if (res) _usbd_mark_ep_complete(endpoint); else if (_usbd_get_ep_status(endpoint) != USB_EP_STATUS_IDLE) res = 26; if (direction == USB_DIR_OUT) bpmp_mmu_maintenance(BPMP_MMU_MAINT_CLN_INV_WAY, false); } return res; } static int _usbd_ep_ack(usb_ep_t ep) { return _usbd_ep_operation(ep, NULL, 0, true); } static void _usbd_set_ep0_stall() { // EP Control endpoints must be always stalled together. usbd_otg->regs->endptctrl[0] = USB2D_ENDPTCTRL_TX_EP_ENABLE | USB2D_ENDPTCTRL_TX_EP_STALL | USB2D_ENDPTCTRL_RX_EP_ENABLE | USB2D_ENDPTCTRL_RX_EP_STALL; } int usbd_set_ep_stall(u32 endpoint, int ep_stall) { usb_hw_ep_t actual_ep = (endpoint & 2) >> 1; usb_dir_t direction = endpoint & 1; if (ep_stall) { if (direction == USB_DIR_IN) usbd_otg->regs->endptctrl[actual_ep] |= USB2D_ENDPTCTRL_TX_EP_STALL; // Stall EP Bulk IN. else usbd_otg->regs->endptctrl[actual_ep] |= USB2D_ENDPTCTRL_RX_EP_STALL; // Stall EP Bulk OUT. } else { if (direction == USB_DIR_IN) usbd_otg->regs->endptctrl[actual_ep] &= ~USB2D_ENDPTCTRL_TX_EP_STALL; // Clear stall EP Bulk IN. else usbd_otg->regs->endptctrl[actual_ep] &= ~USB2D_ENDPTCTRL_RX_EP_STALL; // Clear stall EP Bulk OUT. } return 0; } static void _usbd_handle_get_class_request(bool *transmit_data, u8 *descriptor, int *size, int *ep_stall) { u8 _bRequest = usbd_otg->control_setup.bRequest; u16 _wIndex = usbd_otg->control_setup.wIndex; u16 _wValue = usbd_otg->control_setup.wValue; u16 _wLength = usbd_otg->control_setup.wLength; bool valid_interface = _wIndex == usbd_otg->interface; bool valid_len = _bRequest == USB_REQUEST_BULK_GET_MAX_LUN ? 1 : 0; if (!valid_interface || _wValue != 0 || _wLength != valid_len) { *ep_stall = 1; return; } switch (_bRequest) { case USB_REQUEST_BULK_RESET: _usbd_ep_ack(USB_EP_CTRL_IN); usbd_otg->bulk_reset_req = 1; break; // DELAYED_STATUS; case USB_REQUEST_BULK_GET_MAX_LUN: *transmit_data = 1; descriptor[0] = usbd_otg->max_lun; // Set 0 LUN for 1 drive supported. usbd_otg->max_lun_set = 1; break; default: *ep_stall = 1; break; } } static void _usbd_handle_get_descriptor(bool *transmit_data, void **descriptor, int *size, int *ep_stall) { u8 descriptor_type = usbd_otg->control_setup.wValue >> 8; u8 descriptor_subtype = usbd_otg->control_setup.wValue & 0xFF; switch (descriptor_type) { case USB_DESCRIPTOR_DEVICE: { /* u32 soc_rev = APB_MISC(APB_MISC_GP_HIDREV); usb_device_descriptor.idProduct = (soc_rev >> 8) & 0xFF; // chip_id. usb_device_descriptor.idProduct |= ((soc_rev << 4) | (FUSE(FUSE_SKU_INFO) & 0xF)) << 8; // HIDFAM. usb_device_descriptor.bcdDevice = (soc_rev >> 16) & 0xF; // MINORREV. usb_device_descriptor.bcdDevice |= ((soc_rev >> 4) & 0xF) << 8; // MAJORREV. */ *descriptor = usbd_otg->desc->dev; *size = usbd_otg->desc->dev->bLength; *transmit_data = 1; return; } case USB_DESCRIPTOR_CONFIGURATION: if (usbd_otg->type == USB_GADGET_UMS) { if (usbd_otg->port_speed == 2) // High speed. 512 bytes. { usbd_otg->desc->cfg->endpoint[0].wMaxPacketSize = 0x200; usbd_otg->desc->cfg->endpoint[1].wMaxPacketSize = 0x200; } else // Full speed. 64 bytes. { usbd_otg->desc->cfg->endpoint[0].wMaxPacketSize = 0x40; usbd_otg->desc->cfg->endpoint[1].wMaxPacketSize = 0x40; } } else { usb_cfg_hid_descr_t *tmp = (usb_cfg_hid_descr_t *)usbd_otg->desc->cfg; if (usbd_otg->port_speed == 2) // High speed. 512 bytes. { tmp->endpoint[0].wMaxPacketSize = 0x200; tmp->endpoint[1].wMaxPacketSize = 0x200; } else // Full speed. 64 bytes. { tmp->endpoint[0].wMaxPacketSize = 0x40; tmp->endpoint[1].wMaxPacketSize = 0x40; } } *descriptor = usbd_otg->desc->cfg; *size = usbd_otg->desc->cfg->config.wTotalLength; *transmit_data = 1; return; case USB_DESCRIPTOR_STRING: switch (descriptor_subtype) { case 1: *descriptor = usbd_otg->desc->vendor; *size = usbd_otg->desc->vendor[0]; break; case 2: *descriptor = usbd_otg->desc->product; *size = usbd_otg->desc->product[0]; break; case 3: *descriptor = usbd_otg->desc->serial; *size = usbd_otg->desc->serial[0]; break; case 0xEE: *descriptor = usbd_otg->desc->ms_os; *size = usbd_otg->desc->ms_os->bLength; break; default: *descriptor = usbd_otg->desc->lang_id; *size = 4; break; } *transmit_data = 1; return; case USB_DESCRIPTOR_DEVICE_QUALIFIER: if (!usbd_otg->desc->dev_qual) goto exit; *descriptor = usbd_otg->desc->dev_qual; *size = usbd_otg->desc->dev_qual->bLength; *transmit_data = 1; return; case USB_DESCRIPTOR_OTHER_SPEED_CONFIGURATION: if (!usbd_otg->desc->cfg_other) goto exit; if (usbd_otg->port_speed == 2) { usbd_otg->desc->cfg_other->endpoint[0].wMaxPacketSize = 0x40; usbd_otg->desc->cfg_other->endpoint[1].wMaxPacketSize = 0x40; } else { usbd_otg->desc->cfg_other->endpoint[0].wMaxPacketSize = 0x200; usbd_otg->desc->cfg_other->endpoint[1].wMaxPacketSize = 0x200; } if ((usbd_otg->charger_detect & 1) && (usbd_otg->charger_detect & 2)) usbd_otg->desc->cfg_other->config.bMaxPower = 500 / 2; *descriptor = usbd_otg->desc->cfg_other; *size = usbd_otg->desc->cfg_other->config.wTotalLength; *transmit_data = 1; return; case USB_DESCRIPTOR_DEVICE_BINARY_OBJECT: *descriptor = usbd_otg->desc->dev_bot; *size = usbd_otg->desc->dev_bot->wTotalLength; *transmit_data = 1; return; default: *transmit_data = 0; *ep_stall = 1; return; } exit: *transmit_data = 0; *ep_stall = 1; return; } static int _usbd_handle_set_request(int *ep_stall) { int ret = 0; u8 bRequest = usbd_otg->control_setup.bRequest; if (bRequest == USB_REQUEST_SET_ADDRESS) { ret = _usbd_ep_ack(USB_EP_CTRL_IN); // Set USB address for device mode. if (!ret) usbd_otg->regs->periodiclistbase = (usbd_otg->regs->periodiclistbase & 0x1FFFFFF) | ((usbd_otg->control_setup.wValue & 0xFF) << 25); } else if (bRequest == USB_REQUEST_SET_CONFIGURATION) { ret = _usbd_ep_ack(USB_EP_CTRL_IN); if (!ret) { usbd_otg->configuration = usbd_otg->control_setup.wValue; _usbd_initialize_ep_ctrl(USB_EP_BULK_OUT); _usbd_initialize_ep_ctrl(USB_EP_BULK_IN); usbd_otg->configuration_set = 1; } } else *ep_stall = 1; return ret; } static int _usbd_handle_ep0_control_transfer() { int direction; int ret = 0; bool transmit_data = 0; u8 *descriptor = (u8 *)USB_DESCRIPTOR_ADDR; int size = 0; int ep_stall = 0; u8 _bmRequestType = usbd_otg->control_setup.bmRequestType; u8 _bRequest = usbd_otg->control_setup.bRequest; u16 _wValue = usbd_otg->control_setup.wValue; u16 _wIndex = usbd_otg->control_setup.wIndex; u16 _wLength = usbd_otg->control_setup.wLength; //gfx_printf("%02X %02X %04X %04X %04X\n", _bmRequestType, _bRequest, _wValue, _wIndex, _wLength); switch (_bmRequestType) { case (USB_SETUP_HOST_TO_DEVICE | USB_SETUP_TYPE_STANDARD | USB_SETUP_RECIPIENT_DEVICE): ret = _usbd_handle_set_request(&ep_stall); break; case (USB_SETUP_HOST_TO_DEVICE | USB_SETUP_TYPE_STANDARD | USB_SETUP_RECIPIENT_INTERFACE): ret = _usbd_ep_ack(USB_EP_CTRL_IN); if (!ret) usbd_otg->interface = _wValue; break; case (USB_SETUP_HOST_TO_DEVICE | USB_SETUP_TYPE_STANDARD | USB_SETUP_RECIPIENT_ENDPOINT): switch (_bRequest) { case USB_REQUEST_CLEAR_FEATURE: case USB_REQUEST_SET_FEATURE: if ((_wValue & 0xFF) == USB_FEATURE_ENDPOINT_HALT) { switch (_wIndex) // endpoint { case USB_EP_ADDR_CTRL_OUT: direction = 2; break; case USB_EP_ADDR_CTRL_IN: direction = 3; break; case USB_EP_ADDR_BULK_OUT: direction = 0; break; case USB_EP_ADDR_BULK_IN: direction = 1; break; default: _usbd_stall_reset_ep1(3, USB_EP_CFG_STALL); goto out; } if (_bRequest == USB_REQUEST_CLEAR_FEATURE) _usbd_stall_reset_ep1(direction, USB_EP_CFG_RESET); else _usbd_stall_reset_ep1(direction, USB_EP_CFG_STALL); ret = _usbd_ep_ack(USB_EP_CTRL_IN); } else _usbd_stall_reset_ep1(3, USB_EP_CFG_STALL); break; default: ep_stall = 1; break; } break; case (USB_SETUP_HOST_TO_DEVICE | USB_SETUP_TYPE_CLASS | USB_SETUP_RECIPIENT_INTERFACE): _usbd_handle_get_class_request(&transmit_data, descriptor, &size, &ep_stall); break; case (USB_SETUP_DEVICE_TO_HOST | USB_SETUP_TYPE_STANDARD | USB_SETUP_RECIPIENT_DEVICE): switch (_bRequest) { case USB_REQUEST_GET_STATUS: descriptor[0] = USB_STATUS_DEV_SELF_POWERED; descriptor[1] = 0; // No support for remove wake up. transmit_data = 1; size = 2; break; case USB_REQUEST_GET_DESCRIPTOR: _usbd_handle_get_descriptor(&transmit_data, (void **)&descriptor, &size, &ep_stall); break; case USB_REQUEST_GET_CONFIGURATION: descriptor = (u8 *)&usbd_otg->configuration; size = _wLength; transmit_data = 1; break; default: ep_stall = 1; break; } break; case (USB_SETUP_DEVICE_TO_HOST | USB_SETUP_TYPE_STANDARD | USB_SETUP_RECIPIENT_INTERFACE): if (_bRequest == USB_REQUEST_GET_INTERFACE) { descriptor = (void *)&usbd_otg->interface; } else if (_bRequest == USB_REQUEST_GET_STATUS) { memset(descriptor, 0, _wLength); } else if (_bRequest == USB_REQUEST_GET_DESCRIPTOR && (_wValue >> 8) == USB_DESCRIPTOR_HID_REPORT && usbd_otg->type > USB_GADGET_UMS) { if (usbd_otg->type == USB_GADGET_HID_GAMEPAD) { descriptor = (u8 *)&hid_report_descriptor_jc; _wLength = hid_report_descriptor_jc_size; } else // USB_GADGET_HID_TOUCHPAD { descriptor = (u8 *)&hid_report_descriptor_touch; _wLength = hid_report_descriptor_touch_size; } usbd_otg->hid_report_sent = 1; } else { ep_stall = 1; break; } size = _wLength; transmit_data = 1; break; case (USB_SETUP_DEVICE_TO_HOST | USB_SETUP_TYPE_STANDARD | USB_SETUP_RECIPIENT_ENDPOINT): if (_bRequest == USB_REQUEST_GET_STATUS) { int ep_req; switch (_wIndex) { case 0: ep_req = 0; break; case 1: ep_req = 2; break; case 0x80: ep_req = 1; break; case 0x81: ep_req = 3; break; default: _usbd_stall_reset_ep1(3, USB_EP_CFG_STALL); goto out; } size = _wLength; memset(descriptor, 0, size); if (_usbd_get_ep_status(ep_req) == USB_EP_STATUS_STALLED) descriptor[0] = USB_STATUS_EP_HALTED; else descriptor[0] = USB_STATUS_EP_OK; transmit_data = 1; } else _usbd_stall_reset_ep1(3, USB_EP_CFG_STALL); break; case (USB_SETUP_DEVICE_TO_HOST | USB_SETUP_TYPE_CLASS | USB_SETUP_RECIPIENT_INTERFACE): memset(descriptor, 0, _wLength); _usbd_handle_get_class_request(&transmit_data, descriptor, &size, &ep_stall); size = _wLength; break; case (USB_SETUP_DEVICE_TO_HOST | USB_SETUP_TYPE_VENDOR | USB_SETUP_RECIPIENT_INTERFACE): case (USB_SETUP_DEVICE_TO_HOST | USB_SETUP_TYPE_VENDOR | USB_SETUP_RECIPIENT_DEVICE): if (_bRequest == USB_REQUEST_GET_MS_DESCRIPTOR) { switch (_wIndex) { case USB_DESCRIPTOR_MS_COMPAT_ID: descriptor = (u8 *)usbd_otg->desc->ms_cid; size = usbd_otg->desc->ms_cid->dLength; transmit_data = 1; break; case USB_DESCRIPTOR_MS_EXTENDED_PROPERTIES: descriptor = (u8 *)usbd_otg->desc->mx_ext; size = usbd_otg->desc->mx_ext->dLength; transmit_data = 1; break; default: ep_stall = 1; break; } } else ep_stall = 1; break; default: ep_stall = 1; break; } // Transmit data to HOST if any. if (transmit_data) { memcpy(usb_ep0_ctrl_buf, descriptor, size); if (_wLength < size) size = _wLength; ret = _usbd_ep_operation(USB_EP_CTRL_IN, usb_ep0_ctrl_buf, size, true); if (!ret) ret = _usbd_ep_ack(USB_EP_CTRL_OUT); } out: if (ep_stall) _usbd_set_ep0_stall(); return ret; } static int _usbd_ep0_initialize() { bool enter = false; if (usbd_otg->configuration_set) enter = true; else { usbdaemon->qhs = (volatile dQH_t *)USB2_QH_USB2D_QH_EP_BASE; if (!_usbd_initialize_ep0()) enter = true; } if (enter) { usbd_otg->configuration_set = 0; usbd_otg->max_lun_set = 0; // Timeout if cable or communication isn't started in 1.5 minutes. u32 timer = get_tmr_ms() + 90000; while (true) { u32 usb_status_irqs = usbd_otg->regs->usbsts; // Clear all interrupt statuses. usbd_otg->regs->usbsts = usb_status_irqs; // Check if a reset was received. if (usb_status_irqs & USB2D_USBSTS_URI) { //_disable_usb_wdt4(); // Clear all device addresses, enabled setup requests, transmit events and flush all endpoints. usbd_otg->regs->periodiclistbase = 0; usbd_otg->regs->endptsetupstat = usbd_otg->regs->endptsetupstat; usbd_otg->regs->endptcomplete = usbd_otg->regs->endptcomplete; usbd_flush_endpoint(USB_EP_ALL); } // Check if port change happened. if (usb_status_irqs & USB2D_USBSTS_PCI) usbd_otg->port_speed = (usbd_otg->regs->hostpc1_devlc & USB2D_HOSTPC1_DEVLC_PSPD_MASK) >> 25; // Acknowledge setup request for EP0 and copy its configuration. u32 ep0_setup_req = usbd_otg->regs->endptsetupstat; if (ep0_setup_req & 1) { usbd_otg->regs->endptsetupstat = ep0_setup_req; memcpy(&usbd_otg->control_setup, (void *)usbdaemon->qhs->setup, 8); if (_usbd_handle_ep0_control_transfer()) break; } if (usbd_otg->configuration_set) return 0; if (timer < get_tmr_ms() || btn_read_vol() == (BTN_VOL_UP | BTN_VOL_DOWN)) return 2; } } return 3; } int usb_device_enumerate(usb_gadget_type type) { switch (type) { case USB_GADGET_UMS: usbd_otg->desc = &usb_gadget_ums_descriptors; break; case USB_GADGET_HID_GAMEPAD: usbd_otg->desc = &usb_gadget_hid_jc_descriptors; break; case USB_GADGET_HID_TOUCHPAD: usbd_otg->desc = &usb_gadget_hid_touch_descriptors; break; } usbd_otg->type = type; int result = _usbd_ep0_initialize(); if (result) result = 8; return result; } int usbd_handle_ep0_ctrl_setup() { // Acknowledge setup request for EP0 and copy its configuration. u32 ep0_setup_req = usbd_otg->regs->endptsetupstat; if (ep0_setup_req & 1) { usbd_otg->regs->endptsetupstat = ep0_setup_req; memcpy(&usbd_otg->control_setup, (void *)usbdaemon->qhs->setup, 8); _usbd_handle_ep0_control_transfer(); memset(usb_ep0_ctrl_buf, 0, USB_TD_BUFFER_PAGE_SIZE); } if (usbd_otg->bulk_reset_req) { usbd_otg->bulk_reset_req = 0; return 1; } return 0; } static usb_ep_status_t _usbd_get_ep1_status(usb_dir_t dir) { usb_ep_t ep; if (dir == USB_DIR_OUT) ep = USB_EP_BULK_OUT; else ep = USB_EP_BULK_IN; return _usbd_get_ep_status(ep); } int usb_device_ep1_out_read(u8 *buf, u32 len, u32 *bytes_read, bool sync) { if (len > USB_EP_BUFFER_MAX_SIZE) len = USB_EP_BUFFER_MAX_SIZE; int result = _usbd_ep_operation(USB_EP_BULK_OUT, buf, len, sync); if (sync && bytes_read) { if (result) *bytes_read = 0; else *bytes_read = len; } return result; } int usb_device_ep1_out_read_big(u8 *buf, u32 len, u32 *bytes_read) { if (len > USB_EP_BULK_OUT_MAX_XFER) len = USB_EP_BULK_OUT_MAX_XFER; int result; u32 bytes = 0; *bytes_read = 0; u8 *buf_curr = buf; while (len) { u32 len_ep = MIN(len, USB_EP_BUFFER_MAX_SIZE); result = usb_device_ep1_out_read(buf_curr, len_ep, &bytes, USB_XFER_SYNCED); if (!result) { len -= len_ep; buf_curr += len_ep; *bytes_read = *bytes_read + bytes; } else break; } return result; } static int _usbd_get_ep1_out_bytes_read() { if (_usbd_get_ep_status(2) != USB_EP_STATUS_IDLE) return 0; else return (usbdaemon->ep_bytes_requested[2] - (usbdaemon->qhs[2].token >> 16)); } int usb_device_ep1_out_reading_finish(u32 *pending_bytes, int tries) { usb_ep_status_t ep_status; do { ep_status = _usbd_get_ep1_status(USB_DIR_OUT); if ((ep_status == USB_EP_STATUS_IDLE) || (ep_status == USB_EP_STATUS_DISABLED)) break; usbd_handle_ep0_ctrl_setup(); } while ((ep_status == USB_EP_STATUS_ACTIVE) || (ep_status == USB_EP_STATUS_STALLED)); *pending_bytes = _usbd_get_ep1_out_bytes_read(); bpmp_mmu_maintenance(BPMP_MMU_MAINT_CLN_INV_WAY, false); if (ep_status == USB_EP_STATUS_IDLE) return 0; else if (ep_status == USB_EP_STATUS_DISABLED) return 28; else return 26; } int usb_device_ep1_in_write(u8 *buf, u32 len, u32 *bytes_written, bool sync) { if (len > USB_EP_BUFFER_MAX_SIZE) len = USB_EP_BUFFER_MAX_SIZE; int result = _usbd_ep_operation(USB_EP_BULK_IN, buf, len, sync); if (sync && bytes_written) { if (result) *bytes_written = 0; else *bytes_written = len; } return result; } static int _usbd_get_ep1_in_bytes_written() { if (_usbd_get_ep_status(3) != USB_EP_STATUS_IDLE) return 0; else return (usbdaemon->ep_bytes_requested[3] - (usbdaemon->qhs[3].token >> 16)); } int usb_device_ep1_in_writing_finish(u32 *pending_bytes) { usb_ep_status_t ep_status; do { ep_status = _usbd_get_ep1_status(USB_DIR_IN); if ((ep_status == USB_EP_STATUS_IDLE) || (ep_status == USB_EP_STATUS_DISABLED)) break; usbd_handle_ep0_ctrl_setup(); } while ((ep_status == USB_EP_STATUS_ACTIVE) || (ep_status == USB_EP_STATUS_STALLED)); *pending_bytes = _usbd_get_ep1_in_bytes_written(); if (ep_status == USB_EP_STATUS_IDLE) return 0; else if (ep_status == USB_EP_STATUS_DISABLED) return 28; usb_device_stall_ep1_bulk_out(); return 26; } bool usb_device_get_suspended() { u32 suspended = usbd_otg->regs->portsc1 & USB2D_PORTSC1_SUSP; return (suspended ? true : false); } bool usb_device_get_port_in_sleep() { // Windows heuristic: Forces port into suspend, sleep and J-State. return (usbd_otg->regs->portsc1) == 0x885; } bool usb_device_class_send_max_lun(u8 max_lun) { // Timeout if get MAX_LUN request doesn't happen in 10s. u32 timer = get_tmr_ms() + 10000; usbd_otg->max_lun = max_lun; while (!usbd_otg->max_lun_set) { usbd_handle_ep0_ctrl_setup(); if (timer < get_tmr_ms() || btn_read_vol() == (BTN_VOL_UP | BTN_VOL_DOWN)) return true; } return false; } bool usb_device_class_send_hid_report() { // Timeout if get GET_HID_REPORT request doesn't happen in 10s. u32 timer = get_tmr_ms() + 10000; // Wait for request and transfer start. while (!usbd_otg->hid_report_sent) { usbd_handle_ep0_ctrl_setup(); if (timer < get_tmr_ms() || btn_read_vol() == (BTN_VOL_UP | BTN_VOL_DOWN)) return true; } return false; } void usb_device_get_ops(usb_ops_t *ops) { ops->usbd_flush_endpoint = usbd_flush_endpoint; ops->usbd_set_ep_stall = usbd_set_ep_stall; ops->usbd_handle_ep0_ctrl_setup = usbd_handle_ep0_ctrl_setup; ops->usbd_end = usbd_end; ops->usb_device_init = usb_device_init; ops->usb_device_enumerate = usb_device_enumerate; ops->usb_device_class_send_max_lun = usb_device_class_send_max_lun; ops->usb_device_class_send_hid_report = usb_device_class_send_hid_report; ops->usb_device_get_suspended = usb_device_get_suspended; ops->usb_device_get_port_in_sleep = usb_device_get_port_in_sleep; ops->usb_device_ep1_out_read = usb_device_ep1_out_read; ops->usb_device_ep1_out_read_big = usb_device_ep1_out_read_big; ops->usb_device_ep1_out_reading_finish = usb_device_ep1_out_reading_finish; ops->usb_device_ep1_in_write = usb_device_ep1_in_write; ops->usb_device_ep1_in_writing_finish = usb_device_ep1_in_writing_finish; }