mirror of
https://github.com/CTCaer/hekate.git
synced 2024-12-11 10:42:04 +00:00
282 lines
9.4 KiB
C
282 lines
9.4 KiB
C
/*
|
|
* Copyright (c) 2018 naehrwert
|
|
* Copyright (c) 2018 CTCaer
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify it
|
|
* under the terms and conditions of the GNU General Public License,
|
|
* version 2, as published by the Free Software Foundation.
|
|
*
|
|
* This program is distributed in the hope it will be useful, but WITHOUT
|
|
* ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
|
|
* FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
|
|
* more details.
|
|
*
|
|
* You should have received a copy of the GNU General Public License
|
|
* along with this program. If not, see <http://www.gnu.org/licenses/>.
|
|
*/
|
|
|
|
#include <string.h>
|
|
|
|
#include "di.h"
|
|
#include "../gfx/gfx.h"
|
|
#include "../power/max77620.h"
|
|
#include "../power/max7762x.h"
|
|
#include "../soc/clock.h"
|
|
#include "../soc/gpio.h"
|
|
#include "../soc/i2c.h"
|
|
#include "../soc/pinmux.h"
|
|
#include "../soc/pmc.h"
|
|
#include "../soc/t210.h"
|
|
#include "../utils/util.h"
|
|
|
|
#include "di.inl"
|
|
|
|
static u32 _display_ver = 0;
|
|
|
|
static void _display_dsi_wait(u32 timeout, u32 off, u32 mask)
|
|
{
|
|
u32 end = get_tmr_us() + timeout;
|
|
while (get_tmr_us() < end && DSI(off) & mask)
|
|
;
|
|
usleep(5);
|
|
}
|
|
|
|
void display_init()
|
|
{
|
|
// Power on.
|
|
max77620_regulator_set_volt_and_flags(REGULATOR_LDO0, 1200000, MAX77620_POWER_MODE_NORMAL); // Configure to 1.2V.
|
|
i2c_send_byte(I2C_5, MAX77620_I2C_ADDR, MAX77620_REG_GPIO7, MAX77620_CNFG_GPIO_OUTPUT_VAL_HIGH | MAX77620_CNFG_GPIO_DRV_PUSHPULL);
|
|
|
|
// Enable Display Interface specific clocks.
|
|
CLOCK(CLK_RST_CONTROLLER_RST_DEV_H_CLR) = 0x1010000; // Clear reset DSI, MIPI_CAL.
|
|
CLOCK(CLK_RST_CONTROLLER_CLK_ENB_H_SET) = 0x1010000; // Set enable clock DSI, MIPI_CAL.
|
|
|
|
CLOCK(CLK_RST_CONTROLLER_RST_DEV_L_CLR) = 0x18000000; // Clear reset DISP1, HOST1X.
|
|
CLOCK(CLK_RST_CONTROLLER_CLK_ENB_L_SET) = 0x18000000; // Set enable clock DISP1, HOST1X.
|
|
|
|
CLOCK(CLK_RST_CONTROLLER_CLK_ENB_X_SET) = 0x20000; // Set enable clock UART_FST_MIPI_CAL.
|
|
CLOCK(CLK_RST_CONTROLLER_CLK_SOURCE_UART_FST_MIPI_CAL) = 10; // Set PLLP_OUT3 and div 6 (17MHz).
|
|
|
|
CLOCK(CLK_RST_CONTROLLER_CLK_ENB_W_SET) = 0x80000; // Set enable clock DSIA_LP.
|
|
CLOCK(CLK_RST_CONTROLLER_CLK_SOURCE_DSIA_LP) = 10; // Set PLLP_OUT and div 6 (68MHz).
|
|
|
|
// Disable deap power down.
|
|
PMC(APBDEV_PMC_IO_DPD_REQ) = 0x40000000;
|
|
PMC(APBDEV_PMC_IO_DPD2_REQ) = 0x40000000;
|
|
|
|
// Config LCD and Backlight pins.
|
|
PINMUX_AUX(PINMUX_AUX_NFC_EN) &= ~PINMUX_TRISTATE;
|
|
PINMUX_AUX(PINMUX_AUX_NFC_INT) &= ~PINMUX_TRISTATE;
|
|
PINMUX_AUX(PINMUX_AUX_LCD_BL_PWM) &= ~PINMUX_TRISTATE;
|
|
PINMUX_AUX(PINMUX_AUX_LCD_BL_EN) &= ~PINMUX_TRISTATE;
|
|
PINMUX_AUX(PINMUX_AUX_LCD_RST) &= ~PINMUX_TRISTATE;
|
|
|
|
// Set Backlight +-5V pins mode and direction
|
|
gpio_config(GPIO_PORT_I, GPIO_PIN_0 | GPIO_PIN_1, GPIO_MODE_GPIO);
|
|
gpio_output_enable(GPIO_PORT_I, GPIO_PIN_0 | GPIO_PIN_1, GPIO_OUTPUT_ENABLE);
|
|
|
|
// Enable Backlight power.
|
|
gpio_write(GPIO_PORT_I, GPIO_PIN_0, GPIO_HIGH); // Backlight +5V enable.
|
|
usleep(10000);
|
|
gpio_write(GPIO_PORT_I, GPIO_PIN_1, GPIO_HIGH); // Backlight -5V enable.
|
|
usleep(10000);
|
|
|
|
// Configure Backlight pins (PWM, EN, RST).
|
|
gpio_config(GPIO_PORT_V, GPIO_PIN_0 | GPIO_PIN_1 | GPIO_PIN_2, GPIO_MODE_GPIO);
|
|
gpio_output_enable(GPIO_PORT_V, GPIO_PIN_0 | GPIO_PIN_1 | GPIO_PIN_2, GPIO_OUTPUT_ENABLE);
|
|
gpio_write(GPIO_PORT_V, GPIO_PIN_1, GPIO_HIGH); // Enable Backlight EN.
|
|
|
|
// Power up supply regulator for display interface.
|
|
MIPI_CAL(MIPI_CAL_MIPI_BIAS_PAD_CFG2) = 0;
|
|
|
|
// Set DISP1 clock source and parrent clock.
|
|
exec_cfg((u32 *)CLOCK_BASE, _display_config_1, 4);
|
|
|
|
// Setup display communication interfaces.
|
|
exec_cfg((u32 *)DISPLAY_A_BASE, _display_config_2, 94);
|
|
exec_cfg((u32 *)DSI_BASE, _display_config_3, 61);
|
|
usleep(10000);
|
|
|
|
// Enable Backlight Reset.
|
|
gpio_write(GPIO_PORT_V, GPIO_PIN_2, GPIO_HIGH);
|
|
usleep(60000);
|
|
|
|
// Setups DSI packet configuration and request display id.
|
|
DSI(_DSIREG(DSI_BTA_TIMING)) = 0x50204;
|
|
DSI(_DSIREG(DSI_WR_DATA)) = 0x337; // MIPI_DSI_SET_MAXIMUM_RETURN_PACKET_SIZE
|
|
DSI(_DSIREG(DSI_TRIGGER)) = DSI_TRIGGER_HOST;
|
|
_display_dsi_wait(250000, _DSIREG(DSI_TRIGGER), DSI_TRIGGER_HOST | DSI_TRIGGER_VIDEO);
|
|
|
|
DSI(_DSIREG(DSI_WR_DATA)) = 0x406; // MIPI_DCS_GET_DISPLAY_ID
|
|
DSI(_DSIREG(DSI_TRIGGER)) = DSI_TRIGGER_HOST;
|
|
_display_dsi_wait(250000, _DSIREG(DSI_TRIGGER), DSI_TRIGGER_HOST | DSI_TRIGGER_VIDEO);
|
|
|
|
DSI(_DSIREG(DSI_HOST_CONTROL)) = DSI_HOST_CONTROL_TX_TRIG_HOST | DSI_HOST_CONTROL_IMM_BTA | DSI_HOST_CONTROL_CS | DSI_HOST_CONTROL_ECC;
|
|
_display_dsi_wait(150000, _DSIREG(DSI_HOST_CONTROL), DSI_HOST_CONTROL_IMM_BTA);
|
|
|
|
usleep(5000);
|
|
|
|
_display_ver = DSI(_DSIREG(DSI_RD_DATA));
|
|
if (_display_ver == 0x10)
|
|
exec_cfg((u32 *)DSI_BASE, _display_config_4, 43);
|
|
|
|
DSI(_DSIREG(DSI_WR_DATA)) = 0x1105; // MIPI_DCS_EXIT_SLEEP_MODE
|
|
DSI(_DSIREG(DSI_TRIGGER)) = DSI_TRIGGER_HOST;
|
|
|
|
usleep(180000);
|
|
|
|
DSI(_DSIREG(DSI_WR_DATA)) = 0x2905; // MIPI_DCS_SET_DISPLAY_ON
|
|
DSI(_DSIREG(DSI_TRIGGER)) = DSI_TRIGGER_HOST;
|
|
|
|
usleep(20000);
|
|
|
|
// Configure PLLD for DISP1.
|
|
exec_cfg((u32 *)CLOCK_BASE, _display_config_6, 3);
|
|
|
|
// Finalize DSI configuration.
|
|
exec_cfg((u32 *)DSI_BASE, _display_config_5, 21);
|
|
DISPLAY_A(_DIREG(DC_DISP_DISP_CLOCK_CONTROL)) = 4;
|
|
exec_cfg((u32 *)DSI_BASE, _display_config_7, 10);
|
|
usleep(10000);
|
|
|
|
// Calibrate display communication pads.
|
|
exec_cfg((u32 *)MIPI_CAL_BASE, _display_config_8, 6);
|
|
exec_cfg((u32 *)DSI_BASE, _display_config_9, 4);
|
|
exec_cfg((u32 *)MIPI_CAL_BASE, _display_config_10, 16);
|
|
usleep(10000);
|
|
|
|
// Enable video display controller.
|
|
exec_cfg((u32 *)DISPLAY_A_BASE, _display_config_11, 113);
|
|
}
|
|
|
|
void display_backlight_pwm_init()
|
|
{
|
|
clock_enable_pwm();
|
|
|
|
PWM(PWM_CONTROLLER_PWM_CSR_0) = PWM_CSR_EN; // Enable PWM and set it to 25KHz PFM.
|
|
|
|
PINMUX_AUX(PINMUX_AUX_LCD_BL_PWM) = (PINMUX_AUX(PINMUX_AUX_LCD_BL_PWM) & 0xFFFFFFFC) | 1; // PWM clock source.
|
|
gpio_config(GPIO_PORT_V, GPIO_PIN_0, GPIO_MODE_SPIO); // Backlight power mode.
|
|
}
|
|
|
|
void display_backlight(bool enable)
|
|
{
|
|
gpio_write(GPIO_PORT_V, GPIO_PIN_0, enable ? GPIO_HIGH : GPIO_LOW); // Backlight PWM GPIO.
|
|
}
|
|
|
|
void display_backlight_brightness(u32 brightness, u32 step_delay)
|
|
{
|
|
u32 old_value = (PWM(PWM_CONTROLLER_PWM_CSR_0) >> 16) & 0xFF;
|
|
if (brightness == old_value)
|
|
return;
|
|
|
|
if (brightness > 255)
|
|
brightness = 255;
|
|
|
|
if (old_value < brightness)
|
|
{
|
|
for (u32 i = old_value; i < brightness + 1; i++)
|
|
{
|
|
PWM(PWM_CONTROLLER_PWM_CSR_0) = PWM_CSR_EN | (i << 16); // Enable PWM and set it to 25KHz PFM.
|
|
usleep(step_delay);
|
|
}
|
|
}
|
|
else
|
|
{
|
|
for (u32 i = old_value; i > brightness; i--)
|
|
{
|
|
PWM(PWM_CONTROLLER_PWM_CSR_0) = PWM_CSR_EN | (i << 16); // Enable PWM and set it to 25KHz PFM.
|
|
usleep(step_delay);
|
|
}
|
|
}
|
|
if (!brightness)
|
|
PWM(PWM_CONTROLLER_PWM_CSR_0) = 0;
|
|
}
|
|
|
|
void display_end()
|
|
{
|
|
display_backlight_brightness(0, 1000);
|
|
|
|
DSI(_DSIREG(DSI_VIDEO_MODE_CONTROL)) = 1;
|
|
DSI(_DSIREG(DSI_WR_DATA)) = 0x2805; // MIPI_DCS_SET_DISPLAY_OFF
|
|
|
|
DISPLAY_A(_DIREG(DC_CMD_STATE_ACCESS)) = READ_MUX | WRITE_MUX;
|
|
DSI(_DSIREG(DSI_VIDEO_MODE_CONTROL)) = 0; // Disable host cmd packet.
|
|
|
|
// De-initialize video controller.
|
|
exec_cfg((u32 *)DISPLAY_A_BASE, _display_config_12, 17);
|
|
exec_cfg((u32 *)DSI_BASE, _display_config_13, 16);
|
|
usleep(10000);
|
|
|
|
// De-initialize display panel.
|
|
if (_display_ver == 0x10)
|
|
exec_cfg((u32 *)DSI_BASE, _display_config_14, 22);
|
|
|
|
DSI(_DSIREG(DSI_WR_DATA)) = 0x1005; // MIPI_DCS_ENTER_SLEEP_MODE
|
|
DSI(_DSIREG(DSI_TRIGGER)) = DSI_TRIGGER_HOST;
|
|
|
|
usleep(50000);
|
|
|
|
// Disable display and backlight pins.
|
|
gpio_write(GPIO_PORT_V, GPIO_PIN_2, GPIO_LOW); //Backlight Reset disable.
|
|
usleep(10000);
|
|
|
|
gpio_write(GPIO_PORT_I, GPIO_PIN_1, GPIO_LOW); //Backlight -5V disable.
|
|
usleep(10000);
|
|
|
|
gpio_write(GPIO_PORT_I, GPIO_PIN_0, GPIO_LOW); //Backlight +5V disable.
|
|
usleep(10000);
|
|
|
|
// Disable Display Interface specific clocks.
|
|
CLOCK(CLK_RST_CONTROLLER_RST_DEV_H_SET) = 0x1010000; // Set reset clock DSI, MIPI_CAL.
|
|
CLOCK(CLK_RST_CONTROLLER_CLK_ENB_H_CLR) = 0x1010000; // Clear enable clock DSI, MIPI_CAL.
|
|
CLOCK(CLK_RST_CONTROLLER_RST_DEV_L_SET) = 0x18000000; // Set reset DISP1, HOST1X.
|
|
CLOCK(CLK_RST_CONTROLLER_CLK_ENB_L_CLR) = 0x18000000; // Clear enable DISP1, HOST1X.
|
|
|
|
// Power down pads.
|
|
DSI(_DSIREG(DSI_PAD_CONTROL_0)) = DSI_PAD_CONTROL_VS1_PULLDN_CLK | DSI_PAD_CONTROL_VS1_PULLDN(0xF) | DSI_PAD_CONTROL_VS1_PDIO_CLK | DSI_PAD_CONTROL_VS1_PDIO(0xF);
|
|
DSI(_DSIREG(DSI_POWER_CONTROL)) = 0;
|
|
|
|
// Switch to automatic function mode.
|
|
gpio_config(GPIO_PORT_V, GPIO_PIN_0, GPIO_MODE_SPIO); // Backlight PWM.
|
|
|
|
PINMUX_AUX(PINMUX_AUX_LCD_BL_PWM) = (PINMUX_AUX(PINMUX_AUX_LCD_BL_PWM) & ~PINMUX_TRISTATE) | PINMUX_TRISTATE;
|
|
PINMUX_AUX(PINMUX_AUX_LCD_BL_PWM) = (PINMUX_AUX(PINMUX_AUX_LCD_BL_PWM) & 0xFFFFFFFC)| 1;
|
|
}
|
|
|
|
void display_color_screen(u32 color)
|
|
{
|
|
exec_cfg((u32 *)DISPLAY_A_BASE, cfg_display_one_color, 8);
|
|
|
|
// Configure display to show single color.
|
|
DISPLAY_A(_DIREG(DC_WIN_AD_WIN_OPTIONS)) = 0;
|
|
DISPLAY_A(_DIREG(DC_WIN_BD_WIN_OPTIONS)) = 0;
|
|
DISPLAY_A(_DIREG(DC_WIN_CD_WIN_OPTIONS)) = 0;
|
|
DISPLAY_A(_DIREG(DC_DISP_BLEND_BACKGROUND_COLOR)) = color;
|
|
DISPLAY_A(_DIREG(DC_CMD_STATE_CONTROL)) = (DISPLAY_A(_DIREG(DC_CMD_STATE_CONTROL)) & 0xFFFFFFFE) | GENERAL_ACT_REQ;
|
|
|
|
usleep(35000);
|
|
|
|
display_backlight(true);
|
|
}
|
|
|
|
u32 *display_init_framebuffer()
|
|
{
|
|
// This configures the framebuffer @ NYX_FB_ADDRESS with a resolution of 1280x720 (line stride 720).
|
|
exec_cfg((u32 *)DISPLAY_A_BASE, cfg_display_framebuffer, 32);
|
|
|
|
usleep(35000);
|
|
|
|
return (u32 *)NYX_FB_ADDRESS;
|
|
}
|
|
|
|
u32 *display_init_framebuffer2()
|
|
{
|
|
// This configures the framebuffer @ NYX_FB_ADDRESS with a resolution of 1280x720 (line stride 720).
|
|
exec_cfg((u32 *)DISPLAY_A_BASE, cfg_display_framebuffer2, 32);
|
|
|
|
usleep(35000);
|
|
|
|
return (u32 *)NYX_FB_ADDRESS;
|
|
}
|
|
|